DIY:7th Gen Hood Molding swap - HondaClub.com

**EyesofFreedom** · 02-05-2008, 05:01 PM

Well I originally went with a painted hood molding to match the blacked out front end of my Civic. However the southeast weather was not that nice to it.

To change one out all you need is:

10mm Socket and Rachet
Flat tipped Screwdriver
New Hood Molding

Optional tools:
Rag (to protect paint)
MP3 Player (time flies with music)

This is what it currently looked like...

So after a little searching I found H and A Accessories dot com - Genuine Factory Honda and Acura Accessories at discount prices. Accessories made by Honda and Acura for your car where I could buy a factory painted colored matched unit.

Here is the step by step process to change out the front molding...

First step is to remove the factory unit. It is retained by four nuts...

and then carefully remove the center clip...you will have to insert a straight screwdriver that is small enough to fit into the hole to depress the plastic clip...

Once the unit is removed this is what it will look like...why not clean up the area!

Installation is just the opposite of removal...just insert the center locking pin...and then carefull close the hood so you can center the unit before replacing the nuts.

Here is a pic of the finished effort...

Here is the other for reference...

Total time it took was about 10 minutes and the unit only cost $22.93! A bargain and an easy change to remove the tacky chrome piece!

It is often these small little detail items that are overlooked or postponed to a weekend far off in the distance...that can take an okay look and to good look by tying in everything together!

Versemaster · 02-19-2008, 12:32 AM

kool*

**TJ213** · 02-23-2008, 10:33 AM

Looks good, but you need to clean your car to make it match

**EyesofFreedom** · 02-23-2008, 04:26 PM

man washing the car is too much like work...

no but for real I had washed the car at like 9am...

at 4pm when I did this...it had sprinkled just enough to attach the darn pine pollen all over my car!!!

scott213 · 01-01-2009, 07:34 PM

cool, but have you upgraded this baby since then? u have some new photos posted?

---------------------------------------
I post my articles and reviews here.

kurtdaniel · 07-01-2009, 02:53 AM

yeah i like it,,but much better if the car is cleaner...washing the car is too much work...

02-05-2008, 05:01 PM	#1 (permalink)
EyesofFreedom Official Instigator! Join Date: Jun 2006 Location: Rincon, Georgia United States Posts: 2,098	DIY:7th Gen Hood Molding swap Well I originally went with a painted hood molding to match the blacked out front end of my Civic. However the southeast weather was not that nice to it. To change one out all you need is: 10mm Socket and Rachet Flat tipped Screwdriver New Hood Molding Optional tools: Rag (to protect paint) MP3 Player (time flies with music) This is what it currently looked like... So after a little searching I found H and A Accessories dot com - Genuine Factory Honda and Acura Accessories at discount prices. Accessories made by Honda and Acura for your car where I could buy a factory painted colored matched unit. Here is the step by step process to change out the front molding... First step is to remove the factory unit. It is retained by four nuts... and then carefully remove the center clip...you will have to insert a straight screwdriver that is small enough to fit into the hole to depress the plastic clip... Once the unit is removed this is what it will look like...why not clean up the area! Installation is just the opposite of removal...just insert the center locking pin...and then carefull close the hood so you can center the unit before replacing the nuts. Here is a pic of the finished effort... Here is the other for reference... Total time it took was about 10 minutes and the unit only cost $22.93! A bargain and an easy change to remove the tacky chrome piece! It is often these small little detail items that are overlooked or postponed to a weekend far off in the distance...that can take an okay look and to good look by tying in everything together! __________________ Myspace me... http://www.myspace.com/hondaclub_eyesoffreedom Ferio Project car build page... http://www.my2002ex.mysite.com My other passion... http://www.nscale.org/defaulteng.htm Last edited by EyesofFreedom; 02-05-2008 at 06:13 PM.

02-19-2008, 12:32 AM	#2 (permalink)
Versemaster Junior Member Join Date: Feb 2008 Location: Dallas, Texas United States Posts: 16	kool* __________________ *SKiP*

02-23-2008, 10:33 AM	#3 (permalink)
TJ213 heluva engineer Join Date: Oct 2006 Location: Carlisle, Pennsylvania United States Posts: 1,646	Looks good, but you need to clean your car to make it match __________________ Comma Club Member #1

02-23-2008, 04:26 PM	#4 (permalink)
EyesofFreedom Official Instigator! Join Date: Jun 2006 Location: Rincon, Georgia United States Posts: 2,098	man washing the car is too much like work... no but for real I had washed the car at like 9am... at 4pm when I did this...it had sprinkled just enough to attach the darn pine pollen all over my car!!! __________________ Myspace me... http://www.myspace.com/hondaclub_eyesoffreedom Ferio Project car build page... http://www.my2002ex.mysite.com My other passion... http://www.nscale.org/defaulteng.htm

07-01-2009, 02:53 AM	#6 (permalink)
kurtdaniel Member Join Date: Jul 2008 Location: new york, New York United States Posts: 39	yeah i like it,,but much better if the car is cleaner...washing the car is too much work... Last edited by kurtdaniel; 07-01-2009 at 03:10 AM.

01-01-2009, 07:34 PM	#5 (permalink)
scott213 Junior Member Join Date: Jan 2009 Location: Tallinn, Other/Not listed Estonia Posts: 7	cool, but have you upgraded this baby since then? u have some new photos posted? --------------------------------------- I post my articles and reviews here.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode